Submit search
Freedom 205-1007 Ford Hub-Axle Nut Socket Wrench Alt
Applications:
Failure to apply inward pressure while using this socket will result in the tool not being fully engaged and will break the tabs off the socket.Note: When working on 2015 to current Ford Transits equipped with full floating axles, the right hub nut is right-hand thread and the left hub nut is left-hand thread.
For Ford Tools Catalog click here
Looking for a different Ford tool? Please give us a call!! (909) 334-4400
Shop hard to find auto parts, high-end electrician tools, specialty auto-shop supplies and forestry tools at affordable pricing with FREE Selected Shipping. We specialize in auto, aviation, boat & motorcycle, serving the institutions of military, government, emergency response & education for over 50 years. Find vehicle-specific tools, as well as DIY, boutique hand tools, specialty motorcycle tools to get the job done right.
307-664 Transaxle Case Bushing Installer Alt
Used with 205-153 or ST-214 driver handle.
You'll find Stallion Products are widely considered the most heavy duty on the market! This is a high-quality tool and you will be pleased with your purchase. Don't try to save a few bucks at the expense of your engine - know that you're getting quality from Stallion Products.
For Lincoln Vehicle Tools click here
For Mercury Vehicle Tools click here
Looking for a different Lincoln or Mercury Vehicle Tool? Please give us a call!! (909) 334-4400
Volvo FM12 D13 80mm 6-Point 3/4" Drive King Pin Upper Cover Socket Remover Tool Alt.
Application: VOLVO FM12 D13
This Volvo King Pin Upper Cover Socket 80 mm is a remover tool designed to remove the upper cover of the king pin on Volvo trucks.
This Heavy Duty King Pin Upper Cover Socket Remover Tool, compatible for Volvo (FM12, D13) Trucks. This tool is applicable Volvo FH front axle cover, steering pin (e.g. FM 12).
This King Pin Upper Cover Remover tool have specification of Dr. 3/4", 6 Points, 80 mm and can be used with an impact wrench or torque wrench.
King Pin Upper Cover Socket Remover Tool is manufactured with high quality carbon steel, high strength, anti-wear, rust resistance, anti-oxidation, sturdy and durable.
Also a Volvo Penta Tool
For Volvo Tools Catalogue click here
For Mack Tools Catalog click here
Looking for a different Volvo or Mack Tool? Please give us a call!! (909) 334-4400
Ford 303-126 6883 Pinion Flange Holding Tool for Ford Lincoln Mercury Alt.
Designed to hold drive pinion flanges - universal design with 1/2" slots fits flange bolt centerlines up to 2-5/8"
Fits most Ford, Lincoln, and Mercury drive pinion flanges
Features a 1/2 inch square drive opening in handle for extra leverage
Set includes: Flange Bar, 2ea. 5/16" bolts, nuts, and washers, and 2ea. 3/8" bolts, nuts, and washers
Similar to OE part number 303-126 & OTC 6883
Heavy-Duty Steel Construction, Rugged and durable steel process, finished with non-slip wax to protect from rust and corrosion for long-lasting reliability. With excellent bearing capacity resisting and deformation to carefree service your vehicle engines.
Tillman Ford 6697 Axle Shaft Vacuum Oil Seal Installer Tool for 2006-2019 Ford F-250 F350/450
Fits from 2005 to current Ford F-250 F-350 4x4s with the vacuum-operated front axle. Compatible with OTC 6697.
Helps correctly install the seal into the axle shaft and the wheel knuckle without damaging the seal, prevents front hub vacuum leaks that would cause the 4WD to not engage and covers in oil to prevent corrosion, making your job easier and more proficient.
Made of high quality GB 40CR alloy steel for great strength, prevent corrosion and rust, impact resistance, sturdy and durable. High precision and hardness ensure reliable long-term service.
Mack Truck King Pin Cap Removal Sockets Tool Kit Alternative
This Kingpin Socket tool kit is a direct replacement to OEM parts number J-44004, OTC 5053, CTA 5044 and 11-3000.
Removes and installs thrust bearing adjustment screws on 10500 lb, 12000 lb, 16000 lb, 18000 lb, and 20000 lb axles on Mack diesel trucks.
Includes:
This new design reduces the camming action created by torque and keeps the tool fully engaged in the adjusting screw when removing and installing the cap. May be used with a 1/2 inch square drive ratchet or breaker bar.
Heavy duty steel structure machined and finished with powder coating to resist corrosion and ensure a long-term and reliable performance.
Looking for a different Mack Tool? Please give us a call!! (909) 334-4400
Tillman John Deere KJD10422 Servicegard Seal Installer Alt.
Use to install the king pin seal ring DANA axle
Application: John Deere Equipment
Alternative to OEM KJD10422
For John Deere Tools Catalog click here
Looking for a different John Deer tool? Please give us a call!! (909) 334-4400
Bearing Cup Installer Kit for Dana Spicer SPL 140170 & 250 Alternative to TG10217 or OTC 5191
This cap installation tool set will fit SPL 140, 170, 250 Series drivelines commonly found on class 6 - 8 transportation truck and equipment.
Designed to quickly press the bearing cups on Dana/Spicer SPL 'Life Series' quick-disconnect universal joints for Volvo, Kenworth, Peterbilt, Freightliner, Mack etc.
Our adapters ensure the specific heights for installation to reduce the risk of damage to the driveshaft, yokes, and joint.
Manufactured from high-grade steel to withstand the use of manual or impact tools.
Direct replacement for OEM parts 10217 and 5191.
For Diesel Tools Catalog click here
Looking for a different Detroit Diesel Tool? Please give us a call!! (909) 334-4400
Tillman Toyota 09521-25011-01 Rear Axle Shaft Bearing Puller
Heavy duty and precise built to remove the bearing from the axle but also saving the ABS Sensor.
Used to Pull the Rear Axle Shaft Bearings in Toyota Trucks. Used with 09521-25023-01.
For Toyota Tools Catalogue click here
Looking for a different Toyota Tool? Please give us a call!! (909) 334-4400
Monaco 40122 Dana Spicer Carrier Bearing Adjusting Socket
For D/R170 and D/R180 rear axles on Dana Spicer
Monaco Tool Company manufacture tools to serve the following brands: Caterpillar, Eaton Fuller Transmission, Detroit Diesel, Paccar Engines, Cummins and Navistar.
For Monaco Tools Catalog click here
Looking for a different Monaco Tool? Please give us a call!! (909) 334-4400
Stallion ST-157 Dummy Bearing Set - 205-D047 D81T-4222-DR D-343
Applications: Dana 60 and 70
Spicer & Meritor 1610 1760 1810 Series Heavy Duty Yoke Puller
Direct replacement for Tools 10803 or TG10803.
This extractor was made to fit full and half round yokes on Spicer and Meritor 1610, 1710, 1760,1810 series, Spicer SPL 140, 170, 250 series and Meritor (Rockwell) RPL 20 and 25 series.
Our tool set may be used with a 3/4" impact wrench to generate 25000lbs of pulling power when removing yokes with a bearing diameter of 1 7/8" and 2 3/16".
Designed for the removal of heavy-duty yokes on transmissions, driveshafts, and rear-end differentials without damaging the yoke or other components.
Heavy duty steel structure heat treated, machined and finished with powder coating to resist corrosion and ensure a long-term and reliable performance.
For Transmission Tools Catalog click here
Looking for a different Transmission tool? Please give us a call!! (909) 334-4400
Kent-Moore J-25025-B GM Automatic Transaxle Guide Alignment Pins
Application Automatic Transaxle, Drive Line
Used on: Allure 2005-2006, Aztek-AWD 2001-2005, Aztek-FWD 2001-2005, Bonneville 1998-2002, Cavalier 1998-2005
Manufacturer: SPX/Bosch (OTC Rotunda Kent-Moore Miller)
For General Motors Tools Catalog click here
Looking for a different General Motors Tool? Please give us a call!! (909) 334-4400
Stallion ST-251 9859A 9859 Lower Ball Joint Remover and Installer Tool Alt
Use this special tool with the C-4212F Ball Joint Press to remove and install Lower Ball Joints.
This tool comes with a lifetime warranty!
For Dodge Tools Catalog click here
Looking for Dodge tool? Please give us a call!! (909) 334-4400
KIT4454 Rockwell Meritor Axle Seal Driver Kit R4422401 R4422402 Alt.
This Axle Seal Driver Kit is a direct replacement for OEM parts KIT4454, 2KIT 4454, TDAKIT4454, R4422401 and R4422402.
Our seal installation drivers are required for the replacement of multiple seals for Meritor axles.
Use R4422401 Alt to install 3.00 NOM. DIA. seal and part number R4422402 Alt for 3.25 NOM. DIA. seal.
This seal installer set must be used with a Dead Blow Hammer ONLY to avoid damaging parts and components.
For Heavy Duty Truck Tools catalog click here
Looking for a different Heavy Duty Truck Tool? Please give us a call!! (909) 334-4400
KIT4463 Rockwell Meritor New Style Axle Seal Driver Kit Alt.
Direct replacement for KIT4463 / 2729T1 / 2729T2 / 2730T / 2731T / 2728T1 / 2728T2. Interchanges parts RWKIT4463 / TDAKIT4463 / KIT4463-RI / TDA KIT4463 / 8235-KIT4463 and MERKIT4463.
Required for the replacement of the multiple-lip axle yoke seals for Meritor 14X/16X/18X Single and 14X/16X/18X/38X Tandem Drive Axles. Does Not Apply to Meritor Front Drive Steer Axles, Transfer Cases or Other Drive Axles Not Listed.
Designed to service seal parts number A1-1205Z270, A1-1205X272, A1-1205X2728, A1-1205Y2729, A1-1205Z2730 and A1-1205A2731.
This tool set contains a sleeve and seal driver for the forward-rear input, a sleeve and seal driver for the forward-rear output and two model specific seal drivers for the rear-rear input.
Kent-Moore PT-4370-10 Arvin Meritor 1.7935 FF, FG International Service Kit
For Arvin Meritor MFS-6 (1.2360" King Pin), International FA-223, 224, 226, 227 (1.7885" King pin).Must be used with PT-4375-A.
Service kit includes:
For Kent-Moore Tools Catalog click here
Looking for a different Kent-Moore Tool? Please give us a call!! (909) 334-4400
Volvo 9992671, 9992619 , 9998542 , 9996889 , 88800015 I-Shift Transmission Main Shaft Gear Remover Tool Kit Alt
Application: Volvo I-Shift Transmissions on FM 440 / 500 / FH 540 diesel truck and Renault 43 DXI.
Heavy duty replacement for Volvo OEM parts 9992671, 9992619, 9998542, 9996889, 88800015, 9996315 , 9996081
Hook the tool onto the gear, install the ring to the main body, and turn the spindle to pull out the gear.
Includes Installer adapter set ONI417T alternative to 9996315 & 9996081
Simply install one half of the puller on puller rings together with the hydraulic cylinder, spindle and drift. Install the other half and the hydraulic pump. Remove the high range engaging ring and follow the shop manual to complete the process.
Looking for a different Volvo Tool? Please give us a call!! (909) 334-4400
